qmk_firmware/docs/driver_installation_zadig.md

47 lines
4.4 KiB
Markdown

# Bootloader Driver Installation with Zadig
QMK presents itself to the host as a regular HID keyboard device, and as such requires no special drivers. However, in order to flash your keyboard on Windows, the bootloader device that appears when you reset the board often *does*.
There are two notable exceptions: the Caterina bootloader, usually seen on Pro Micros, and the Halfkay bootloader shipped with PJRC Teensys, appear as a serial port and a generic HID device respectively, and so do not require a driver.
We recommend the use of the [Zadig](https://zadig.akeo.ie/) utility. If you have set up the development environment with Msys2 or WSL, the `qmk_install.sh` script will have asked if you want it to install the drivers for you.
## Installation
Put your keyboard into bootloader mode, either by hitting the `RESET` keycode (which may be on a different layer), or by pressing the reset switch that's usually located on the underside of the board. If your keyboard has neither, try holding Escape or Space+`B` as you plug it in (see the [Bootmagic](feature_bootmagic.md) docs for more details). Some boards use [Command](feature_command.md) instead of Bootmagic; in this case, you can enter bootloader mode by hitting Left Shift+Right Shift+`B` or Left Shift+Right Shift+Escape at any point while the keyboard is plugged in.
Some keyboards may have specific instructions for entering the bootloader. For example, the [Bootmagic Lite](feature_bootmagic.md#bootmagic-lite) key (default: Escape) might be on a different key, e.g. Left Control; or the magic combination for Command (default: Left Shift+Right Shift) might require you to hold something else, e.g. Left Control+Right Control. Refer to the board's README file if you are unsure.
To put a device in bootloader mode with USBaspLoader, tap the `RESET` button while holding down the `BOOT` button.
Alternatively, hold `BOOT` while inserting the USB cable.
Zadig will automatically detect the bootloader device. You may sometimes need to check **Options → List All Devices**.
- For keyboards with Atmel AVR MCUs, the bootloader will be named something similar to `ATm32U4DFU`, and have a Vendor ID of `03EB`.
- USBasp bootloaders will appear as `USBasp`, with a VID/PID of `16C0:05DC`.
- AVR keyboards flashed with the QMK-DFU bootloader will be named `<keyboard name> Bootloader` and will also have the VID `03EB`.
- For most ARM keyboards, it will be called `STM32 BOOTLOADER`, and have a VID/PID of `0483:DF11`.
!> If Zadig lists one or more devices with the `HidUsb` driver, your keyboard is probably not in bootloader mode. The arrow will be colored orange and you will be asked to confirm modifying a system driver. **Do not** proceed if this is the case!
If the arrow appears green, select the driver, and click **Install Driver**. The `libusb-win32` driver will usually work for AVR, and `WinUSB` for ARM, but if you still cannot flash the board, try installing a different driver from the list. For flashing a USBaspLoader device via command line with msys2, the `libusbk` driver is recommended, otherwise `libusb-win32` will work fine if you are using QMK Toolbox for flashing.
![Zadig with a bootloader driver correctly installed](https://i.imgur.com/b8VgXzx.png)
Finally, unplug and replug the keyboard to make sure the new driver has been loaded. If you are using the QMK Toolbox to flash, exit and restart it too, as it can sometimes fail to recognize the driver change.
## Recovering from Installation to Wrong Device
If you find that you can no longer type with the keyboard, you may have installed the driver onto the keyboard itself instead of the bootloader. You can easily confirm this in Zadig - a healthy keyboard has the `HidUsb` driver installed on all of its interfaces:
![A healthy keyboard as seen by Zadig](https://i.imgur.com/Hx0E5kC.png)
Open the Device Manager and look for a device that looks like your keyboard.
![The board with the wrong driver installed, in Device Manager](https://i.imgur.com/L3wvX8f.png)
Right-click it and hit **Uninstall device**. Make sure to tick **Delete the driver software for this device** first.
![The Device Uninstall dialog, with the "delete driver" checkbox ticked](https://i.imgur.com/aEs2RuA.png)
Click **Action → Scan for hardware changes**. At this point, you should be able to type again. Double check in Zadig that the keyboard device(s) are using the `HidUsb` driver. If so, you're all done, and your board should be functional again!